When I press the button open and close doors its
If the parking lights are flashing when you attempt to start the vehicle, it is an visual notification to you as to the reason WHY it doesn't start.
Six flashes of the parking lights is (-) or (+) shutdown and seven flashes is neutral safety shutdown. These are the most common reasons for remote starter malfunction. The (-) shutdown relates to the hood pin switch. A malfunction in this area occurs when the hood pin switch fails to make contact with the hood when closed. Adjusting the pin or the bracket it may be attached to will solve the problem. The (+) shutdown relates to brake wire. Unless you have your foot on the brake while attempting to remote start, the issue could be with the brake switch or the wire making contact with 12 volts during remote start operation. The neutral safety shutdown relates to either the toggle switch or, if this is a new installation, the thin black with white stripe wire NOT being connected to ground. If your remote starter has worked before and, is not working now, the issue will be with the toggle switch. The toggle switch will be located (usually) under the dash near the left kick panel. The kick panel is where your left would rest when driving.
3/24/2011 3:59:10 AM •
1600XP...
•
Answered
on Mar 24, 2011
My remote start does not
Make sure if you have a mercury switch not to park on the hill because the mercury inside the switch is going to make contact like the hood is open, if not put attention if this happen only when is windy, check the engine and trunk pin switch.
How do i get the security system out of valet
From remote: press F twice on the remote then unlock. (F, F, Unlock)
From car: have door open, turn key to ignition position (ON), then OFF, then press and release the button on the control center (antenna on the windshield).
hope this helps.
Installed a python 991 on 1997 ford mustang and
Make sure the unit is programmed to automatic transmission (if this is a automatic transmission vehicle). Make sure the switch is actually in the on position and not off (mislabeled). Check the hood shutdown pin switch and make sure that it is making contact with the hood when closed. Check the connection for the black/white wire.
Have a Python 990 and
The antenna icon signals that the return data from the central unit hasn't been received - which means that either the antenna in the central unit or the processor have failed. Basically the alarm is dead, beyond repair, you will have to replace it. And you must find out if there's an external cause to the failure: as a shorted wire or a failed sensor, or a disconnected cable.
Python ce0890 FCC ID EZSDET474P RPN 473P 266
While our Dodge ram truck sits - the horn starts blowing. We think it has to do with the remote and the security. We have the Python CE0890 remote starter - it is a few years old.
I am attempting to install a Python 1401 in my
Make sure that the neutral safety wire (small black with white) sees a chassis ground. If you connected the toggle switch to the wire, confirm that the other side of that wire is connected to a good ground. Confirm that the hood pin switch wire (gray) is NOT seeing ground during remote start. All of the above are relevant for a vehicle with an automatic transmission. If the clicking sound that you hear is also flashing the parking lights, that is a remote starter error message. Six flashes concern the hood shutdown (-) or the brake shutdown(+). Seven flashes concern the neutral safety shutdown.
Car starts but dies as soon as you put it in gear
if you start the car with the remote start you can not put the car in gear until the key is inserted into the ignition and turned to the on position. the vehicle will just die if this is not done.
1/22/2011 9:17:24 PM •
Install...
•
Answered
on Jan 22, 2011
My wife threw away our
You don't know what kind of car you have? I can tell you how to find it to disconnect it as long as you tell me what kind and year of catr you have and that country your in.
I recently purchased a 1996
Hi,
You can download and print the instruction manual in PDF format from this
link.
On the page which opens, select the model number from the drop-down list and then download the manual.
Adobe PD Reader is required to view this manual.
Download Adobe Reader
If your model number is not included the list, kindly contact the Python support on
1-800-753-0600.
Hope this helps. Thanks for using
FixYa.
The vehicle starts but runs only for about 1
you need to re-program your factory alarm bypass module. if you haven't used on then you will need to find out which one you need for the vehicle and install it. Check the Viper/DEI Website for details.
If your module is in, check the Can Hi and Low connections to be sure they are to the correct wires.
1/6/2011 3:59:28 PM •
1600XP...
•
Answered
on Jan 06, 2011
Remote strater is in valet
Try these two possible solutions
Press and hold valet button for 10 seconds. Release. LED should go out.
or
Insert key into ignition. Turn to on position (do not turn on car). Press and hold valet button for 10 seconds. Release. LED should go our
1/4/2011 6:33:25 PM •
533 2way...
•
Answered
on Jan 04, 2011
Not finding what you are looking for?
