3I can fix that!
Anonymous posted an answer for this Saws:
"two key tricks-- use a block of wood to keep the blade from turning,(you might need three..."
Anonymous
Anonymous posted an answer for this Plumbing:
"Most likely either the shutoff valve or the fill valve is not opening correctly or is..."
AnonymousAnonymous posted an answer for this Saws:
"Sounds to me like you have a bad cord. Clamp the saw to a workbench so that it can start..."
Anonymous
Anonymous posted an answer for this Grinders:
"If you can't measure it directly, take the nut with you to a hardware store and find a..."
Anonymous
Anonymous posted an answer for this Cycling:
"If you are talking about the handle-bar stem, the bolt you need to tighten is right in the..."
AnonymousAnonymous posted an answer for this Saws:
"21 cm is 8-1/4 inches. You could use an 8 inch blade or 7-1/4. But the diameter of the..."
Anonymous
Anonymous posted an answer for this Lutron LG-600P Lumea Single-pole 600 Watts Incandescent Dimmer:
"These are probably three-way switches being used as two-way. If so, then the switches..."
Anonymous
Anonymous posted an answer for this Measuring Tools & Sensors:
"You probably have a broken valve spring. Try a compression test. If this is the..."
Anonymous
Anonymous posted an answer for this Leviton Decora Light Dimmer Switch:
"Are these remote controlled dimmers? Do you have failing batteries in one of the remotes?..."
Anonymous
Anonymous posted an answer for this Skilsaw "5150" Circular 7 And 1/4 Inch:
"Yes, it overheated. Not worth fixing, replace it. What happens is that with a very heavy..."
Anonymous
Anonymous posted an answer for this Electrical Supplies:
"Yes, replace it. But once you have it removed, you might want to check it with a..."
Anonymous
Anonymous posted an answer for this Makita Jigsaw Blade:
"Tom, The one for metal will almost certainly have the smallest teeth. Sometimes the..."
AnonymousAnonymous posted an answer for this Electrical Supplies:
"Not sure of your application, but in most cases a three speed motor has two sets of coils..."
Anonymous
Anonymous posted an answer for this Tools & Hardware - Others:
"I can't imagine that the scratches are coming from the blade. If the blade was damaged,..."
Anonymous
Anonymous posted an answer for this Diamondback Joker 20 Boys' Freestyle BMX Bicycle:
"John, If this is a one-piece crank (both crank arms and the axle are all one piece) then..."
AnonymousAnonymous posted an answer for this Saws:
"Remove the belt and try to spin the blade. If it still acts that way, you need to..."
AnonymousAnonymous posted an answer for this Drills:
"Take the old belt to an auto parts store."
Anonymous
Anonymous posted an answer for this Delta Machinery Delta 34-555 Sliding Table Attachment - Right-Tilt 10 inch Contractor's or Unisaws:
"Left-tilt, right-tilt refers to the direction the top of the blade can be tilted when it..."
AnonymousAnonymous posted an answer for this Saws:
"Here's a link to an article I wrote several years ago. It also includes a handy..."
Anonymous
Anonymous posted an answer for this Dremel 5 3" Saw Blades 8033 For 550 Moto-saw:
"Try going to a store that sells scroll saws and look at the new models to see how they..."
Anonymous
Anonymous posted an answer for this Craftsman 3/8 in. Drill Press Bit, Mortising Chisel:
"If you use a brad point bit or forstner bit or any bit that cuts around the circumference..."
AnonymousAnonymous posted an answer for this Tools & Hardware - Others:
"The two sizes (in the US) for router bit shanks (and collets) are 1/4 inch and 1/2 inch. ..."
AnonymousAnonymous posted an answer for this Electrical Supplies:
"First confirm that you have current available on the 120 leg by trying a lightbulb (use..."
AnonymousAnonymous posted an answer for this Saws:
"On any saw blade, you will loosen the nut (or bolt) in the direction that the teeth of the..."
AnonymousAnonymous posted an answer for this Electrical Supplies:
"When any switch or circuit breaker is turned on, and there is a load present, there will..."
Anonymous
Anonymous posted an answer for this Craftsman 10" Table Saw:
"You probably need to replace the bearings on the arbor shaft. If you have the means to..."
Anonymous
Anonymous posted an answer for this Delta Machinery Delta ShopMaster DP350 12" Variable Speed Bench Drill Press, 500-3100 RPM, 1/3 HP:
"I assume this is a solid pin that isn't tight enough. Replace it with a rollpin. Google..."
Anonymous
Anonymous posted an answer for this Delta TP305 12 - 1/2" Portable Planer:
"This is called snipe and it is a common problem. There are two feed rollers, one before..."
AnonymousAnonymous posted an answer for this Delta TP305 12 - 1/2" Portable Planer:
"This is called snipe and it is a common problem. There are two feed rollers, one before..."
Anonymous
Anonymous posted an answer for this GE 18023 Dimmer Rocker OnOff with Slide White:
"Bob, Not quite enough info to be sure how you have this wired, but here's a shot. 3 or..."
Anonymous
Electrical Supplies 154 answers
Garden 147 answers
Saws 115 answers
Cycling 102 answers
Home 59 answers
Tools & Hardware - Others 43 answers
Drills 33 answers
Air Tools & Compressors 26 answers
Plumbing 23 answers
Measuring Tools & Sensors 18 answers
